top of page
ISS banner.jpg

OnSite Security 
Testing Utility

This form will walk you through conducting a self-test with your alarm system for the Door Contacts and Interior Motions in 2 easy steps!  This Self-Test will take approximately 15 minutes.

1 PANDA INN

Your Security Zones

Below is a listing of zones identified for your location to test.  You will use this for reference.

1
FRONT DOOR CONTACT
2
ROOF HATCH DOOR CONTACT
3
LOBBY/OFFICE GLASS BREAK
4
OVERHEAD WAREHOUSE DOOR CONTACT
5
LOBBY/OFFICE MOTION
6
REAR WAREHOUSE MOTION 360
7
FRONT WAREHOUSE MOTION
9
GATE ENTY CONTACT
10
SIDE WAREHOUSE DOOR CONTACT
11
AC UNIT CONTACT 1
12
AC UNIT CONTACT 2
13
AC UNIT CONTACT 3
14
AC UNIT CONTACT 4
1
FRONT DOOR CONTACT
2
REAR ENTRY DOOR CONTACT
3
SERVICE DOOR CONTACT
4
EMERGENCY DOOR CONTACT
5
ROOF HATCH CONTACT
6
FRONT ENTRY MOTION
7
REGISTER MOTION
8
FRONT DINING MOTION
9
OFFICE MOTION
10
BAR MOTION
11
REAR ENTRY MOTION
12
REAR DINING MOTION
25
BACK DINING MOTION
26
CENTRAL POS MOTION

TO PERFORM TEST, SYSTEM MUST SHOW GREEN READY LIGHT ON THE KEYPAD.

THIS REQUIRES NO MOVEMENT IN THE RESTAURANT.

Step 1

Start by placing the Alarm system in Test Mode at the Keypad.  

  • Enter the code 4112 (this code is used for testing the Alarm System only)

  • Then Press 5

  • Then press "0" for "0=Walk"

  • You will hear a short 2-second siren blast. The siren will be loud, please alert additional staff in the store for preparation. This is normal and means the battery is operating in the panel correctly.

Step 2 keypad.png

Step 2

Begin testing the Door Contacts and Interior Motions.

We recommend testing with a colleague:  one person to walk the floor, and one person by the keypad watching the display. When a device within a zone is triggered, you will hear a chime at the keypad. The keypad will display "Fault" with the zone number or zone description.

Fault 3 keypad.png

Once you close the zone, or the zone clears, the display will return to showing "Test In Progress".

Test in Progress keypad.png

To test a Door Contact, open and close the door.

To test an Interior Motion sensor, we recommend walking across the path of the motion, and under the motion (please see example image below).

Testing Interior Motion Sensors-2.png

Mark a PASS if you heard the chime and saw the zone on the keypad.

Mark a FAIL if you did not hear the chime and did not see the zone on the keypad.

Zone ID

Zone Description

Pass/Fail

1

FRONT DOOR CONTACT

Pass

Fail

Please select a result!

2

ROOF HATCH DOOR CONTACT

Pass

Fail

Please select a result!

3

LOBBY/OFFICE GLASS BREAK

Pass

Fail

Please select a result!

4

OVERHEAD WAREHOUSE DOOR CONTACT

Pass

Fail

Please select a result!

5

LOBBY/OFFICE MOTION

Pass

Fail

Please select a result!

6

REAR WAREHOUSE MOTION 360

Pass

Fail

Please select a result!

7

FRONT WAREHOUSE MOTION

Pass

Fail

Please select a result!

9

GATE ENTY CONTACT

Pass

Fail

Please select a result!

10

SIDE WAREHOUSE DOOR CONTACT

Pass

Fail

Please select a result!

11

AC UNIT CONTACT 1

Pass

Fail

Please select a result!

12

AC UNIT CONTACT 2

Pass

Fail

Please select a result!

13

AC UNIT CONTACT 3

Pass

Fail

Please select a result!

WHEN FINISHED, ENTER YOUR 4-DIGIT CODE, THEN PRESS 1 TO REMOVE FROM TEST MODE.

Great job!

Thank you for completing the self-test!

Your responses will be reviewed by Interface Systems, and appropriate steps will be taken as necessary.

Have a great day!

Your content has been submitted

bottom of page